Leaderboard

As far as I'm aware because it's not an alarm and does not need to be linked you need to get something like this https://scotlandhomesafe.co.uk/collections/carbon-dioxide/products/domestic-carbon-dioxide-monitor These seem to be what most people have around here and I have the same one, wall mounted so you can see the screen.

Are you sure you are correct stating that. You need CO for any combustible appliances, gas boiler wood stove etc. It is also mandatory to have a CO2 if your airtightness is better than 15. This is a stand alone monitor mains powered. https://www.gov.scot/publications/building-standards-2017-domestic/3-environment/314-ventilation/ Section 3.14.2 applies

In Scotland, (not sure about rest of UK, if you have a high airtightness, below 3ACPH (IIRC) you do need to monitor Carbon 'Di'oxide.

A**hole abusive threatening n'bors' Onoff, unfortunately. But thankfully that tiny sliver up there is their backward/ farthermost bit. And the bank immediately below that ladder/ scruffy top bit, actually is not theirs. Almost vertical steep to stream. We're uncomfortably close unfortunately, but, they have a mass of overgrown bamboo & a general established bigh "forest" of xyz plants hiding them from me 90%. Prior owners gardening experts you see, these two (since 2 yrs) not a clue so its all going haywire ott.. helping privacy a bit. zoot.

Bit of a worthless and obnoxious comment. I certainly had no issues with the product or the company.

New build in progress. Carpenter asking how much gap to leave off floor for door frame (if I understood correctly). Plan is to use underlay & carpets. He suggested 20mm. Is that good advice?

About time, think how much grief it will save self builders.

Worth checking that two of these can be joined together. You might need a short length if pipe between the two?

Hi, My name is Lori,thank you for accepting me on building hub. Can anyone give me any advice on how to take bitumen paint of a victorian gable end Or am I better just leaving it and point the gable end with lime ?

Use the 135/45° bends but make sure you joint them using something like CT1 especially onto that horizontal outlet as they will leak otherwise.

got this is an email shot from Toolden. might interest the black and yellow brigade of which @pocster is the leader

Another pretty picture from the usual source. You can multiply zero (left graph) by a 1000, but you will still get... not much. Unless a conversation/text about GW, renewables etc. starts with "we recognise we can't even talk about not using FF anytime soon" I personally won't listen as the speaker simply lies to me.

The door only opens on one of them!!!, decent threshold strip to join them (and make sure the threshold strip is exactly under the door or it looks crap 🤔)

Timber alu clad, generally speaking no, the water is allowed to drain behind the cladding and the window cill sits further back (always refer to manufacturer or supplier for clarity on product you're looking at).

Have the video camera and at least you might get £250 if it all goes t!ts up!

Something like..... .....strap a couple of 4.8m scaffold boards atop the Genie arms, parallel to the roofs. You need to get the load dead centre. Lay 3 decent ratchet straps across the boards. Handball the roll onto the boards so if 5.5m you'll only have 350mm overhanging each end. The ratchet straps will be under the roll. Lift to height. Ideally a tad higher than the roof. Next strap 3 more boards from the "Genie" boards, to the roof. Ladder job to get up there. Roll off down the slope and watch it go straight across the roof and off the opposite edge! 😂

Agreed but are you having MVHR? As then you will need more. My pet hate is doors that “scrub” carpets. I used to put a 2” strip of hardboard between frame uprights to kick the carpet up to the door when closed but allows the door to swing missing the carpet (just).

It really comes down to what the building inspector will let slide on the day. The regs specifies mains and a visual display, no mention of it being integrated and no problem with it being on the ceiling. That certainly looks nicer, no mention of being able to record data over the past 24 hours but I would seriously doubt any one is going to care.

No, to be fair it is right. Common to have a CO2 in master bedroom in Scotland, it does not need to be on the interlinked fire alarm system though as it's not a fire alarm. CO for combustion appliances, usually done with a combined CO/optical head.

The CO2 alarm doesn't need to be part of the fire alarm, it is just a monitor/warning alarm if the CO2 ppm gets too high, you get staged alerts then a danger level. Maybe if houses were built with proper ventilation rather than stupid sealed boxes. I have just finished a residential development of 36 flats just outside of Glasgow, we omitted the CO2's a design stage because we could prove the MVHR system would provide suitability fresh air.

The levelling spacers are typically removed by hitting them side on with a mallet (or kicking them if on the floor)

Could be gap for door itself or he may mean the frame to allow wood or tiles to slot underneath. I have just done some frames with 15mm underneath and wish I had left more … it was a pig of a job slotting the 8mm click fit planks under with 5mm underlay. 20mm under a door for underlay and carpet sounds pretty good

It still needs to be mains operated, have a visual display and be capable of logging C02 data for the last 24 hour period. That would rule out the Aico Temperature, Humidity and CO2 Environmental Sensor. unless it can connect to a visual display. It looks like that would mean getting the Ei1000G SmartLINK Gateway and connecting it to a laptop. I'm not sure that would meet the easy to use and understand part of the requirements, it's also more expensive than just getting the standalone monitor and having it wired in somewhere on a wall.

Yep . Seen detached and yet I’d struggle to walk down it . Best one was my brother many years ago bought a new build with a garage . He had an average size car . It would fit in the garage but you couldn’t open the doors to get out!. Absolute joke these ‘ developers’ . Yet try and do a single self build and all those ‘ignored’ rules are suddenly applied and enforced .

Thanks everybody. I've found long radius 22.5 and 45 bends and my local builders yard. Because of the distance I need a chamber regardless (need one every 20m) so I think I'll put in the bend just downstream of a standard chamber. I'll skip the chamber for the second bend as it's right before the last MH anyway. Seems to be the best value and fastest option... Only got the digger for the weekend so don't want to spend half a day benching and building chambers!

I think you can do either. I used both of the following: 1. 45 deg bends at the entry and exit of the straight through run of a 3 or 5 way to make a 90 bend. 2. A long rad 45 bend with no chamber at it. The theory being a long rad bend should rod through from the closest chamber. Where I did it nearest chamber was about 6m away. BC were happy with all I did. Give them a call for confirmation.

Our LA required a minimum of 22 metres separation on upstairs facing windows between our new build and an existing property on adjacent plot. And yet the same LA has permitted national house builders to erect new builds in the same Borough with upstairs facing windows less than 9 metres apart. Go figure 🤔

Yes it does. However, there are now several lime products to go on woodfibre IWI, for example, that are very easy to apply, so much so that a typical plasterer will find it easy, possibly easier, to work with than gypsum - nicely workable and long set time. An example is Lime Green Solo as part of the IWI system - https://www.lime-green.co.uk/warmshell/warmshell-interior. Baumit also sell products well regarded in this area. This piece does highlight that local climate is very important, and that driving rain can have a significant effect on the performance of the wall. You're going to find variations in suggested buildups. I would personally like to see an update of this as it's from 2010. The Bristolians guide to insulation suggest 0.60. https://sdfoundation.org.uk/wp-content/uploads/2018/01/2015_bristolsolidwallinsulationguidance.pdf. There are lots of other links in some recent posts that go into a lot more detail about approaches to IWI.

Yes that’s fine or you can do it the old way with benched bends in brick built chambers.

The post 8 hours states CO2, you then said the spec was wrong without further explanation. Scottish Building regs require a CO2 monitor not CO2 alarm. So the word alarm is incorrect. Also in Scottish Building regs the use of combined heat and smoke alarms are not allowed, as only a heat alarm is allowed in a kitchen. It even makes a comment about combined units in a kitchen will not comply with the regulations.

yes - Cramer / Fugi tools come with plastic runners that stop the tool dropping into the gaps and following the tile profile.

yes pencil round but it is quite deep radius to about half the thickness of the upstand. You can hide it by reversing it

Sorry, just read up on the 10yr rule; I now understand that hmrc view 'conversion' and '10 Yr rule' renovation as effectively the same thing. Every day's a school day!

Will try the LithofinPower-Clean as recommended by @PeterW Reluctant to use acid unless I really have to and equally the same with bleach .

We used to get rest bends and cut the top out and sit a small size chamber over it notched and concreted in with a lid

Isoquick mentions earthing the slab in their tech spec. First electrician I engaged thought it was pointless but told me to fix an earth rod to the rebar coming up in the plant room. Second electrician saw the rod and cut it off

This is a response from a company that does insulated raft slabs, about @Iceverge's idea about a timber insulated raft foundation:

Ours hob extracts to the outside and is pretty powerful. If it over powers our MVHR it hasn't complained 🙂 It clearly bypasses the heat exchanger in the MVHR so must reduce efficiency but its probably only used a few hours a week so the effect would be small.

You can also see the reclaim form here. Search it for "10 years". It asks you to provide evidence its been empty. Try council tax dept? https://www.gov.uk/government/publications/vat-refunds-for-diy-housebuilders-claim-form-and-notes-for-conversions-vat431c Some other things to think about... VAT: I know you plan to live in it but if circumstances change, do not rent it out without seeking tax advice. If you let out the property you may have to repay any VAT you saved under the scheme. This is because letting income is VAT exempt not zero rated. The difference may seem trivial but if something is exempt it means you can't reclaim so called "input vat" on your costs. House sales are zero rated so you can. Its not clear if this also applies to something like a property let via AirBnB. CIL: You mentioned a loft conversion. If this is big (close to or over 100sqm) you should check out the CIL rules. If they apply you might be exempt but only if you claim the exemption before work starts. The 100sqm rule is the total increase in floor area so it might apply if a small extension and loft conversion together add more than 100sqm.

In short.. If you buy materials from a builders merchant you pay 20% and reclaim 20%. If a tradesman supplies and fits materials then they charge you 5% on both labor AND materials and you reclaim 5% on both. In detail.. The important thing is to pay any trades you hire the correct 5% rate. If you pay 20% VAT on labor you can't reclaim it later as HMRC won't refund VAT paid in error. So when you get quotes make sure they say VAT at 5%. If not ask for them to be amended before you accept them. Some trades may question this if they aren't familiar with the rules. It may help if you give them a "certificate". This is essentially a letter from you stating that the work they are to carry out is on a property being reinstated after 10 years empty. Include your contact details, the site address and any planning permission reference numbers. There might be a template in VAT 708 or someone here can probably post one they wrote. If someone quotes to "supply and fit" then both their labour and materials should be 5% rated. Some trades may not like this as they pay 20% when they buy them. This should be sorted out when they make their VAT return but some trades still worry about it. If any refuse to 5% rate your only option is to buy materials yourself paying 20% and reclaiming 20% later. You can then "free issue" the materials to the trade to fit. The downside is the trade might get a better discount than you. Under no circumstances must anyone live in the building before work starts as that resets the 10 year clock. However i believe you can move in a few days after work starts if necessary. T

Possibly worth looking at something like Lithofin Power-Clean which is very good at ingrained dirt on stone. It’s alkaline so doesn’t dissolve like an acid will.

Getting there slowly. The bond pattern is working out ok. Main issue I'm having is that the stone isn't a constant thickness. The difference between thick ones and thin ones is 3mm. Overall I don't think its great quality stone but it will look ok when done. Lucky I have so many to cut I can cut off defects. Any tips for removing these levelling spacers?

You've got to be a bit careful with reading these documents as the reference note in paragraph 48 points to this: You really need someone who can run it through a proper analysis like with WUFI before arriving at a buildup for yourself. You still have the challenge of how to create and maintain a fully sealed and effective vapour control layer throughout the building if using PIR. The detailing thus being imperative. I personally don't understand the popularity of PIR in these circumstances because of the detailing and added risks, particularly when you have a preferred option of moisture open solutions available to you. The alternatives will not only reduce your risks but also tend to provide a nicer indoor air environment because of their breathability. This can in turn reduce the demands on additional ventilation requirements.

Ha, I did no modelling, no calculations just pure logic, and it worked 👍

I built my own silencer. worked very well. Next time i would combine and build my own manifold/silencer like @joe90 did. I would consider building a soundproof cupboard for the MVHR UNIT too. You can hear it when the door to the utility is open.

That's not a tree it's a mirror!

Might suit @SteamyTea ; he likes arranging flowers . Or maybe @Onoff ; he needs something to trim his bush

Ask 100 architects for an eco solution, you get 100 wrong answers, at least.

Interesting subject... large isolated conductive structure. Might be able to harvest a small amount of power from local radio transmitters. Or make it into a radio telescope if no transmitters nearby. If it were mine I'd definitely want to be able to make a connection to it.

Ah, right. Paint it white.