Mr Punter

It would be really useful if someone did an on line 3d print service for house models from autocad.

Our contractors used the Klober permo type product in the past under a zinc roof. It has a layer of what looks like course trimmed pubic hair to create a gap.

Perhaps a strong coffee and a cigarette tomorrow morning, following tonight's kebab, will allay any scruples and see it properly christened.

If this is for your basement and you have waterproof membrane you need to use 50mm I stud and it can be independent of the wall. If you wedge a bit of insulation behind them it stops any rattle.

Combined with your underpinning this is a decent structural milestone. I assume from the DPM your insulation is on top of the concrete?

20 tonne.

@EverHopefull the post is about SDLT, not council tax. To get the property removed from the council tax register you may need to remove the roof as a minimum and perhaps demolish internal walls and remove and board over doors and windows. They don't want people owning properties that can easily be made habitable and not paying council tax. @Ferdinand the SDLT rates seem quite similar - so much so I am surprised there has been a court case. It looks like the property would have to be in excess of £1M to bother.

I was just looking at an overage clause for a friend the other day. It was in favour of the Church of England and was 34% of the difference between the original purchase price and the uplifted value after planning consent. Duration was 21 years. I am a layman but it looked tightly worded including the assumption for the revised valuation that all services, rights etc were in place. They paid £30k for a plot which will be worth £250k with consent. They were a monopoly bidder as the site was landlocked, the only access being through land owned by the friend. 50% for 50 years I would tell them to do one.

They are when a fire gets into the cavity, because timber is flammable and masonry is not.

Villeroy & Boch wall hung on a Geberit type frame. 300mm between wall and WC. We have reduced this to 250mm in other units where soil pipe location dictates. It gives 400mm-450mm between sink unit and WC.

Sprinklers will not put out a fire in a strongly vented cavity, but they should stop it reaching there. I still can't believe how fire stopping / cavity barriers are such a design / specify / install on the hoof thing where correctly installed they could save lives and buildings. I would liken it to buying a car and being left to work out how to fit seatbelts and airbags.

I have a very similar setup but the 1650 measurement is 1700. The WC is pushed away from the sink a bit, rather than centred, and no issue getting to the sink.

Hilti gun fastenings are used a fair bit for metal ceiling systems.

We have in the past used 75mm blocks for slate hanging and 100mm for render so they match depthwise.

Are you no longer having the roof as a drive-on area? Also, are you planning on doing a plasterboard ceiling under the concrete?

@pocster I think he is asking if you are going to suspend people?

If it were me I would spend more on a better area. Maybe a small cottage in a decent village where you could extend would be a better bet. You will never make money in a poor location.

This is so typical and as per the other thread it is because nobody is made responsible for specifying, designing and installing this that it so frequently get omitted. Generally with rainscreen cladding you are supposed to have a strongly ventilated gap from bottom to top of your cavity. This is very much at odds with the principal of cavity barriers, which prevent the flow of air (and fire) between each storey of a building horizontally. You can get intumescent firestopping that expands when heated which would work for the horizontal, but it is very costly. I got some from Envirograf. It is also sensible to have some vertical barriers to restrict spread of fire around the building so you could divide it up near the corners for example by stapling the red sausage vertically. The fibre cement is a good move. It is also good to have fire retardant breather paper, but you will normally get what you are given by the t/f co.

@ultramods it looks great. For me it would take some getting used to the small prep and serving space, toaster, radio etc but there is a decent amount of storage. I am hoping there is somewhere for a bean-to-cup coffee machine, otherwise I will not be buying.

No issues at all with this, especially as they are non-loadbearing.

No. Remove the unsafe wall and replace it with a fence. If you are concerned, email highways informing them of your intention.

I have used Guttercrest in Shropshire to supply ali stuff. If you give them a call they may be able to put you in touch with someone to install.

The installer's insurance should cover this. If they are criminally negligent, ceasing trading would not remove personal liability.

Just seen what else they make!! I am sure you have space for a few more... https://www.siegersystems.co.uk/products/thermally-broken-floorlight/

If you have different cladding and you want to maintain a flat finish between them you may need to increase the batten size for the render. Hardie also do starter trims, corners etc in varying depths.