Pocster

I’m just worried if I do that and it still leaks I’ll never get it out .( between seal and tray I mean )

Reckon SWMBO might not notice the water …

I have a leak from the ensuite waste . Tested this ages ago all fine . SWMBO has a shower - slight leak . I manage to tighten the trap half a turn - leaks even more !! Can’t see anything obvious. Trap seems good , rubber seal seems good . Underside of tray hole is a bit tight to that timber - but as you can see in photo’s it’s not catching in . Is there perhaps a different / better trap I can use ???

https://ifunny.co/picture/u9KOXawe2

Naughty bitch boy !

Philistines !! ? ?

Confused here ? wine or whine ? ? In our previous property had a cheap beko dishwasher - was fine . But the Bosch is much quieter and has app link up ( sad I know ) …

Got a Bosch ( can dig out the model number ) very quiet . I can swear / drink wine and no one says “ is the dishwasher on “ ….

A sea of Black and Yellow!. HEAVEN!

Eclisse . Right pita to fit and company were assholes also . Looks good though ?

Never a shortage of screws when i pb ?

SWMBO ??

There Steamy (expletive deleted)ing knob bored. I AM THE MAN!

Any suggestions of a material I can use to sound insulate the cupboard it is in?

I know , I know - I was just stroking your member . Just surprised how long and noisy it’s been on - 78% even now . Will fiddle bathroom ufh up - you going to do the same ?

SWMBO wants the same - everything works when server fails ? Looked at hc2 - wasn’t that impressed - but hc3 May be better . SWMBO wanted ‘real ‘ light switches in bedrooms . So have zwave ones that also function as ‘normal ‘ touch switches i.e can turn a load on/ off regardless of HA functioning . I have zero battery powered devices so aeotec sensors for example are poe . Battery failure and polling / update issues I can see being an issue so eliminated that problem . My lighting is automatic ( don’t want 50 switches on the wall ? ) or via an iPad to control .

Simple lol ? - I don’t do that ! For ufh I have solus actuators on each run . Then a heatmister ( I think ) wiring loom with fibaro switches . So zwave turns on the fibaro switch ; which opens the actuator - the wiring loom sees this and starts the pump . Heating !! ? z wave for lighting kind of works ! ( z wave not 100% reliable ) . Aeotec sensor detects movement in room and triggers zwave din rail switch to turn light on . If you need more specific’s just ask ! Just ordered 2 new aeotec sensor 7 - see if they they improve the reliability/ delay between a light coming on . Homeseer scripting does the work .

I agree ; couldn’t see the point of temperature at the floor . I have aeotec multi sensor 6’s in the ceiling in each room . Temperature reading is just 1 of their functions . But it is zwave so you would need a server ….

I assumed ( maybe incorrectly) this unit auto boosts ( though it still says ‘low ‘ ) on high humidity . Just surprised how noisy and slow it is - bathrooms been clear for ages !! . 80% now . Just want to check this is normal operation ….

Yeah I was in a rush to wire it and didn’t give a fudge . Sparky liked it also ??

On what joint ?

80% now. I think it goes normal at 75%??? No one better shower after 10pm!!!

Ok. Now 81% Surely I want to increase the boost setting?? To reduce the humidity very quickly ( even if very noisy )? By adjust the terminal - you mean the air intake in the bathroom?. I don't think there is any adjustment on it .... If there is do I want to open it more or reduce it??? Did think maybe my humidity/condensation drain might be the issue i.e. not enough fall ; but I think looks ok....

Still noisy now and still 82%. Even turned if off/on ( technical approach ) still the same. Unless it quietens down will have to turn it off as won't be able to sleep later.

The internal humidity shows at 82% ( was 83% ) seems to be taking a long time though to drop......