Jump to content

Copper or Aluminium nails for slate?


Recommended Posts

Do not go with aluminium as they are really soft and if you hit a knot or even hard bit of wood they bend, you then try and get them out and the heads rip right off...... i got given a load as the local roofers will not use them..... copper every time.   

  • Like 1
Link to comment
Share on other sites

21 hours ago, Construction Channel said:

anyone got a strong opinion on this?

 

Aluminium:

-cheaper

-supposedly weaker

-corrosion resistant

 

copper:

- Just bloody expensive

-what most people consider the nail for slates

 

Slightly surprised you aren't making your own :-)

  • Like 1
Link to comment
Share on other sites

11 minutes ago, Ferdinand said:

 

Slightly surprised you aren't making your own :-)

 

 

10 minutes ago, Barney12 said:

 

With yours and Fay's initials on each head :D

 

 

let's not be silly you two. I haven't finished making a solitary brick out of free clay yet, I doubt I'll get these made by the weekend....

 

but if I was going to press my own nails, yes I would try to put an E&F on the head ;) 

Link to comment
Share on other sites

Now i am not saying this is a good idea especially as i used copper after all my free aluminium ones  drove me mad.... but what is the actual life expectancy of galvanised clout nails  when used in a non harsh environment under a good quality slate roof ? Just asking.  

Link to comment
Share on other sites

33 minutes ago, Cpd said:

Now i am not saying this is a good idea especially as i used copper after all my free aluminium ones  drove me mad.... but what is the actual life expectancy of galvanised clout nails  when used in a non harsh environment under a good quality slate roof ? Just asking.  

You will probably get 50-60 years out of them, but you might see the rust staining before that. That's how bodgit and scarper roofers would do it

  • Like 1
Link to comment
Share on other sites

  • 7 months later...

I'll be nailing directly into 22mm Sarking board

 

interesting point about not piercing the felt

 

the build up is OSB panel, covered in membrane, covered in sarking board, another membrane, slates.

 

so Sarking will be nailed through roofshield that's left by the panel company.

Link to comment
Share on other sites

not according to the sips company, no, 22mm sarking required.

 

it does seem strange, I'll admit

 

oops, forgot one important thing

membrane, with battens at 600mm, then sarking, membrane, slates

 

important thing to forget

Edited by Tin Soldier
  • Like 1
Link to comment
Share on other sites

  • 5 years later...

Not sure if this is the right place to put this but here goes. I have a SIPS panel roof with a membrane. Battened and counter battened with 25mm yellow battens. The roofer said he would use copper clouts on the slates but has actually used aluminium nails. The warranty provider inspected the roof at the time and said it was acceptable. The next inspector has indicated that he will not warranty the roof with aluminium nails in. I paid for copper nails so I am very disappointed that they weren't used. Am I going to have an issue in the long term with the fact that they used the wrong nails? I wanted a slate roof so that i didn't get a build up of moss and I understand (now) that it is the properties of the copper nails. Any comments.

Link to comment
Share on other sites

5 hours ago, AndreaICF said:

The warranty provider inspected the roof at the time and said it was acceptable. The next inspector has indicated that he will not warranty the roof with aluminium nails in.


Got it in writing from the first inspector ..??

 

5 hours ago, AndreaICF said:

I wanted a slate roof so that i didn't get a build up of moss and I understand (now) that it is the properties of the copper nails.


Not sure who’s told you that but copper nails don’t stop moss - you can get it on any roof. Copper nails don’t corrode as quickly which is why they are used with slates.
 

Aluminium nails are fine with tiles as usually tiles are hooked over the battens and therefore if the nail fails then the tile doesn’t move.

 

Link to comment
Share on other sites

I've got 350m2 of expensive Cupa slates, put on sarking boards (scotland) by my roofers. All done with aluminium nail and looks great. 

 

I wouldn't worry at all about aluminium nails. 

 

I also have a SIPS roof. Sips panel, breather membrane, 25mm battens, 22mm sarking boards, second breather membrane then slates. 

 

I've also got the over fascia vents, and ridge roll to allow airflow underneather the sarking. 

Link to comment
Share on other sites

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...