ToughButterCup

Meinst du Grohe ? Hier, Junge.

And good humour ...

He's got a wooden leg, a seriously broken nose, every tooth in his head is false and suffers from the worst dose of haletosis I've ever seen. His wig is usually on back to front and he dresses like Greg or Terry on the Simpsons. Apart from that he's a good bloke.

[...] The only thing I would add to what J has said is to change is to may be - as changed above. Why? It depends on whether -locally- there are strict criteria to follow - or whether the decision depends on the judgement of the Officer concerned. I suspect the latter is the case. Your application looks to me to be perfectly acceptable. Stick to your guns.

I found that stitch drilling is faster. A mate called round yesterday. His name might as well be Russell Griffiths. "You got a stud finder?" Yes "Used it?" ? Reaches into my tool bag and roots around. Brings out the Teuton Stud / Bar / Wire finder. Scrapes around on the wall. Waits til it goes green. Marks the spot. You know what happens next. Sometimes I can't see the wood for the trees. 6 more holes to go. ?

Nothing is obvious to me, nothing: until I've got it wrong three times and learned the hard way. No, the plastic fitting is NOT tapered. What difference (tapered or not) does that make? The brass fitting is tapered a bit, though. Thanks both. Ian

Have look at this please ..... Don't I need some sort of seal / O ring in the brass check-valve? Ian

So, how does your practice reduce the risks associated with that problem?

Exactly right. @JSHarris warns - often - about the perils of stepping across that divide And doesn't the process of negotiating a brief mean there's a conversation . And nobody spending an average of £250,000 ( a guess) is going to simply ' ... then stand back ... ' are they? It's a partnership: and those require effort and emotional intelligence.

There you go @SteamyTea

The lack of precisely that: lack of knowledge, causing very significant levels of stress.

Yes, that's how I gained my students' attention : especially with Post Graduates - the more experienced the student, the sharper the intake of breath. And among those whose false teeth I had knocked out in the process, none of them even asked for first aid or Aspirin. Remarkable - never, even once! Your comment highlights the importance of communication - it (or rather the lack of it) goes to the heart of the question (rant) of the OP. It's normal for people to talk and listen past one another: everyone does it, on occasion, needs to even. But in our context - a high stakes, highly charged, high stress environment, the soft skills involved become very important indeed. CDM 2015 points out that we are Domestic Clients. People who are assumed not to have any significant levels of expertise. And so that imposes an additional level of responsibility on the architect; embodied in part in the profession's Code of Professional Behaviour and Ethics. There is an explicit therapeutic relationship between client and expert here. It is a great pity that the Code says nothing at all about the importance of effective communication - the profession does by implication in the matter of requesting Third Party Review. (requesting the details by which a decision was made ). From your experience, what lies at the heart of good communication between client and architect?

So, once you've identified the problem - and it's possible cause(s) , what do you think you might do to improve the situation?

Excellent! You've identified a CPD opportunity for yourself. Do you have any idea why some of your clients glaze over as you speak?

So a frame isn't structural? I learn stuff every day. Must be a clueless self-builder. Less clueless than I was a few moments ago then eh?

Hmm, show me.

In my experience, that price depends on the factors outlined in my post above. As our scaffolder put it; "I can't buy enough certified scaffolding at the moment"

There's a local group who have done just that. A very welcoming bunch they are too: regularly hold Open Days. Right next to the M6, Lancaster North. Worth a trip ?

Yes. But, by the time I'd hit the bloody rebar I was so committed, so annoyed (with my own lack of forethought), soooo over-focused. And to think I used to give lectures to hundreds of students on the role that emotion plays in the learning process. ?

Ermmm, had a look - nuffin.

Shut yer face Graves. ? Sounds like you've done it more than once.....

Remember those joists I put in? Well they've come back to bite me again. Trousers on this time. Because a quirk of fate often known as lack of experience , instead of putting in a duct through a wall ready for the MVHR ducting, I have to drill a series of large holes (160 square) through a concrete wall - easy you'd think. Why the fuss? Well, while putting up the POSIs I could have foreseen the need to drill through the wall, but - yes reader, you are there before me. Because I had my nickers in a twist about getting the first floor in, I just had to get the damn POSIs in. Just had to. So, I put the bloody things in - the first 50mm from the wall (so proud of myself for getting that bit right) and carried on, pleased as punch that I was doing it on my own - reasonably successfully. 400 centres. Comes the time to drill the holes. Got the hammer drill (a trusty Teuton Special), got the long SDS+ drill bits. Shoo shoo ! Can't get the drill and the bit between the friggin joists can I? 400 mm centers nowhere near wide enough. Poke it through the gaps - Naah - only let's me drill 10mm. Bugger. I know, pop round the other side and stitch drill from there. Whoo hoo, all's well - except the damn drill keeps binding half way through. The drill kicks and binds - often. Because of where I have to jam myself to make the hole, the kicking drill hits my top lip, thumps my thumb - I've only got 8 of the damn things left for Gods sake. Humour was in short supply. I'd only gone and forgotten how much bloody rebar I'd put in the friggin wall. Enough to ballast Boaty Mc Boat-Face. The drill was binding on the rebar. Warra pillock! Out comes the other Teuton. The Zigger zagger (chop saw). Buggers the blade up in short order. Out comes the third bit of kit all the way from The Fatherland (well, ermmm China) . New Diamond blade, new battery, that'll get the bastard. The rebar is deep in the wall, to reach it, have to hold the angle grinder by the base. Sparks, noise, masses of dust - me suited and visored like Darthvader, can't see a thing. The grinder jams and jerks . Pinches my hand in the hole. Hard. The dust clears to find me hands jammed between my legs in pain, swearing like a trooper and sweating like the sinner that I am. Anyone know how to tell if there's rebar in the concrete you're about to drill? Please? Pretty please?

Hello @ChrisSig. I know exactly how you feel. I've been there. The imminent change in the rools is not as bad as it sounds: it'll make no difference to the hundreds of thousands of other people who are in exactly the same situation as you. It will make differrence if you are proposing to sell. But, for now don't worry. Nowt is going to change on the stroke of midnight. First, follow @Temp's advice. then follow @ProDave's In terms of unhappy-chappie farmers and bogginess (what's new?) - offer to dig a drainage pipe (£250 per day plus machine hire plus stone, pipe and some form of membrane ) to the nearest sensible place : where does that bank lead to ?

By any standards, this thread contains ,for the most part, a good discussion. Good because anyone who chooses can engage with the core ideas and make their own mind up. Were I not full-time on my own on my build, I'd have a good go at summarising it : the process of doing that well would teach me a great deal. Here's a go at a one (OK, 2) liner; Because the term Thermal Mass is both commonly used and seen by some as problematic, its use should be qualified. That qualification should be given with reference to factors commonly understood to be involved in Thermal Stability. In other words, ask the person using the term for clarification.

If I could offer a hopefully helpful word or two. The term 'lead' doesn't matter. You'll need them to work together - well. Start with either trade, doesn't matter - if they're at all experienced, they'll know who to work with. But do check them both out thoroughly. Good excuse to go down and have a drink in their pub, and listen. You can safely leave unconnected panels on the roof. Good luck! Piccies, please! Ian