Search the Community
Showing results for tags 'aluminium'.
-
Hi, We are building a house in the Outer Hebrides with Plannja hard finish coated Aluminium specified for the roof in the coastal environment. I’m trying to get hold of Plannja in Sweden but they aren’t responding and their only UK distributor that I know of is Nu Style of Aberdeen and all you get from their automated phone answer is “this office is closed” which suggests they have ceased trading. Anyone know of a good supplier of hard coated 18mm aluminium sinusoidal roofing sheets and flashings? It’s only around 160sq m we need and I don’t want to use steel as I need something highly durable. Thanks, Nick
-
I have steel beam on the outside skin. Thinking of Aluminium windows above and below. I'm thinking if inner part of widow frame touches flange of beam then thermal bridging in the frame is lost. Maybe encase beam with insulation? So how best to insulate beam? TIA
- 11 replies
-
- i beam
- insulation
-
(and 3 more)
Tagged with:
-
Does anyone know of a good window cill cover supplier? A few of mine (as yet unfitted) were mis-appropriated by the roofers and used as flashing for the solar PV, so I need some more. ? 'Taint funny.
- 16 replies
-
- aluminium
- window cill
-
(and 2 more)
Tagged with:
-
Evening All. Its along story ...so i will condense. Basically Window company was supplying some bi-folds to go with our chartwell green UPVC theirs was aluminium ...and they asked is for a RAL ....we told then couldnt they just match it and that said they worked off RAL etc etc anyway the net result of all this is that RAL 6021 looks NOTHING like chartwell green ...far far darker So we decided to have them sprayed ...as the "blame game" was going on forever .... A company came out and try as they might they did not have a tape that would stick to the internal rubber seal to mask it ... no problem they said ....we will pull it out ....its a wedge gasket 5 minutes later they handed me a bunch of varying lengths of rubber and said "keep them clean and pop them in once its all dry and unmasked! I had to hand it to them their paint colour was SPOT ON ...but ..... when i went to put the gaskets in 2 days later ...no way would they go...tried using thin tools ..plastic tools euro wedges everything ... any more pressure and the glass would break for sure. Now along came the joiner and he noticed that around the aluminium doors was a detachable profile ...and after a bit of a wiggle and waggle it came loose BINGO ! ...so off i went with silicone spray and a plastic scraper and squeezed it into the profile ...as i THOUGHT it should go ....but it doesn't LOOK right and when i try to clip the profile back on its like there is TOO MUCH rubber on the other side or something ..it must be in wrong So i am hoping someone can tell me how to proceed ..I have some pics of the detachable profile and a rough image of the gasket cross section PS as you look at the pic...the LONG corner of the profile is the bit that sits deep in and effectively under the glass edge...and the tall flattest section is the one that faces into the sun-room. I know the bead MUST go into that rectangle notch some way ...but how is the question What a palava !
-
Is 3g worth the investment over 2g? We have a lot of windows and doors, including sliders etc, altogether we're looking at 200m2 over 70 items. I've had around 10 quotes now and the feedback from the window companies has been to stick with 2g (possibly because they know it's cheaper and therefore within my budget) however, it seems the majority of you guys have 3g and you all seem to know what you're doing! I would say that my main priorities are equally: Quality (highly rated, long warranty etc) Aesthetics (They have to suit the contemporary style of the house, the slimmer the better) Cost (I'm trying to get a LOT of house for the money so would be glad to just get the shell made, sealed and clad leaving the rest to be finished bit by bit) I've had quotes from all the main players mentioned on here selling Alu clad as well as some Aluminium frame companies and there are many pro's and cons with each. Initially I was pretty set on 3g but I simply can't ignore the potential additional cost, it could be the difference between getting the project started right away or waiting a while longer to save up the necessary funds. I'm even considering flush casement plastic windows as they look pretty decent but I'm yet to be convinced. Ultimately, this is our forever home and as such, I really don't want to make a decision I'll later regret. P.S - We're not building a passive house but it will be as air tight as we can make it (ICF construction married to brick and block)
-
Had most of my Windows fitted last week and this week they came to fit the sliding patio doors. I wanted bifold but because of cost compromised with sliders. It was suggested that I have 3 panels with 2 sliders to maximise the opening by a different company. The quote came through with 2 fixed panels which was counter productive in having a wider opening. I phoned up and explained what I wanted and that I that the single panel should be on the opposite side to that given on the quote and received an email confirming both instructions. The door came with 2 fixed panels and one slider. They were getting it in to position when I luckily went to look and saw it wasn't right and told them. It is a father and son company and the son is my contact. The father went ballistic saying they'd told me I couldn't have 2 sliders. Slammed everything down, threw everything back in the van and drove off with tires squealing. I got an email the next day from the son apologising for his dad's behaviour but reiterating that they had told me I couldn't have 2 sliders. I know that they can be made with 2 or even all 3 sliding. I was offered them by another company and have seen them online. However I am now wondering what to do. I am definitely not having the doors that have been made. They are just wrong. but Do I get them to make me some standard 2 piece doors? Do I source 3 way sliders from somewhere else? And if so do I go for UPVC, which I know will be bulky, or aluminium Or Do I pay the extra and get bifolds Another setback as of course whichever option I choose there is a lead time putting back me being watertight Thoughts please
- 21 replies
-
- 1
-
- patio doors
- sliders
-
(and 2 more)
Tagged with:
-
Hi all. I need to create two frames from 2"x3" 10SWG hollow section aluminium (6082 T6). Am thinking I should weld them so I need to buy the kit to do it - need to update my 45 year old arc welder as well. I know the @Onoffspeaks well of this model which with associated TIG kit sounds like a working solution for under £300. Any other recommendations or thoughts?
- 14 replies