Pocster

Some of them aren’t inserted fully . The problem was the 2 tees needed ‘adjusting’ simultaneously to fit . If I do One bit and let it set it Won’t line up with the other Bit . I was reluctant to glue it all with a ‘tick tock’ over my head but couldn’t see any other way of doing it

Fecking star ⭐️ Didn’t even know that existed . Yes I’ll do it on all those joints just as a precaution .

Ok . I had to glue 4 joints all at once to get this to fit . Tried it dry was tricky anyway . Given I have about 30 seconds top I did ok - but some of the joints aren’t as tight as they should be . Is this ‘ok ‘ ? . Will water test in 30 mins . Assume some CT1 around all joints would do no harm . Second lesser issue . The thicker 50mm white pipe was going to be my AAV run that I wanted to boss strap after the toilet ( end of the drain ) . Can’t see how I can do that now . I can fit it after the toilet ( but before anything else ) - is this likely to cause issues ?

Appreciated. It’s reassuring when someone says it’s ok . I pretended to attempt to sit on the loo - and it’s seemed ok . No good for @Onoff mind - lardy arse .

The sink to the left would have a 10mm gap . Moving it right just to centre the mirrored wall unit . Can’t have wall unit off centre to the sink

I need to shift the sink 25mm to the right . Wall unit is 55cm wide . Those upright edge to edge are exactly 55cm apart . So with tile backer , adhesive , tile I need to gain 25mm So sink would be about 10mm over the geberit frame ...

Acceptable ??

Spirit level on floor represents shower tray edge ... Funny how a relatively large ensuite shrinks !!!!

Skinny asses ! Not sure what you mean . That rear wall is a false wall . Too the right of the WC will be a shower enclosure .

How much can I move right ? Can I go right to the edge of the geberit frame ? My next problem now is recessed mirror requires cutting out that vertical timber the frame is attached to . How do I cut it vertically off but still have the frame supported strongly ?

What about this ? Just feels really tight on the left . Once I board ( just tile backer ) and then tile . Also got to fit a recessed mirror unit above it .

Knob !!! can go left of the Wc but makes unit quite tight to the wall !!! What a bomb brain !

Oh bollocks ! i was desperate to get a small sink for the ensuite But Its in the way of the WC !! What a #*% I am ! ?

I always thought this was a dark blackish colour . I ordered a bathroom vanity unit ages ago and just opened it . Box says anthracite - unit looks ‘grey’ - is this right ???

And that spinning / raising bloody shower head thing ! ?

Yeah I need to dig that out

Got another fan . Still no joy !

Just had an RK door installed. yes - pricey! But sooooo worth it!

True. Still looks tight too me . Also the Geberit original destructions do only show fitting from stud into metal frame. You didn't do it the Geberit way!!! UMMMMMM!!! ?

Well! This one didn't work. Might just be the wires need swapping around... https://www.ebay.co.uk/itm/1PC-12V-Mini-Cooling-Computer-Fan-Small-40mm-x-10mm-DC-Brushless-3-pin-JC/193264503219?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

Just ordered some self tapping screws at 100mm long so will just screw through the timber into the metal frame . Less hassle than breaking the cistern !

Whats "Gently" mean???

Call to geberit - told me not to remove the cistern . Their advice drill a pilot hole into the steel then use a wood screw ! Not happy with that . Think I need long self tapping screws - can then drill through timber from the outside - then use screw that bites the steel properly.

Hey @Onoff What am I doing wrong here ? Managed to get 1 bolt in but the rest are basically inaccessible - does the actual cistern come out or something ? . Don’t see how I can get a bolt from the outside in and hold the nut ...

Hey @Onoff What am I doing wrong here ? Managed to get 1 bolt in but the rest are basically inaccessible - does the actual cistern come out or something ? . Don’t see how I can get a bolt from the outside in and hold the nut ...