SteamyTea

What that spreadsheet I did about 10 years ago was all about. Just looked at the probability of condensation forming over a period of time. May have to revisit this problem as adding in evaporation would make it more accurate.

Going to pop that on the Kindle, will also show that screens at night don't disturb sleep I am sure.

Welcome. Having done 3 renovations in the past, I wish I had made that decision early on. Would have saved time, money and mess.

Was that one of the 3 or 4 topics that got locked in a day. So can I discuss the upcoming Grand Tour? Or is that going way too far. @Onoff I have never had an official reprimand. I shall start to behaviour even more badly now.

Are they known as Type 4, or is that MCBs. Too lazy to Google (TLTG).

I would have told them to (expletive deleted) off, I hate those things at so many levels.

Think that was the problem with the SMAs. Some had a transformer and some didn't. Seem to remember that the TL range should not have an RCD as it caused problems.

Can depend on inverter, RTFM on that one. Not had any experience of that. Was it wired and then a test certificate issues?

Someone will find a way around it I am sure.

Inexperience, got the same when I was a lad.

I may have to make one, but without the Crapple code.

I know what you mean, my new one is metal.

Can't you just set up a small, cheap computer that has Bluetooth, when it detects a known Bluetooth signal with a registered MAC address, it then can do what you want it to do. Might even be able to use those cheap 'lost luggage and car keys' Bluetooth fobs to activate it.

I am a bit of a fan of, um fan heaters. They heat the air quickly, are cheap to buy and cost the same to run as any other resistance heater. But there is a problem. They are usually controlled by a mechanical, bi-metalic, thermostat. This can either switch the whole unit off, or just switch the heating element off. If the whole unit is switched off when the desired temperature is reach, it is easy to forget it is actually on. This is a bit annoying if I go out for the day as it costs a bit as it is using day rate on the E7. What I would like to do is fit a timer, which is easy enough, but also control the temperature better. So what would be a reliable, cheap and fairly easy was of controlling not just the power of the element, but also the fan speed. Reducing the fan speed, in proportion to the output power woudl keep the noise down. I don't mind the speed and power being high when it is first switched on, but it would be usefully if it reduced power as it comes up to a set temperature. And be always being on, there would be some fan noise as a reminder to switch it off.

With all the energy to drive that lot, be better off just opening a window.

These were a water saving idea. They should have been a soap saving idea as you learnt the first time that there was not enough water to wash it all off.

Then can I go around and change them for 100 quid, they cost about a quid each.

Are they DHT11s, these are rubbish. The DHT22s are a lot better.

Are these the ones that use the mains water pressure to draw the hot from a vented cylinder. The sort the cheapskate don't buy as we get the cheapest pump from Screwfix. Or the ones that pull in air?

Yes as part of the MCS yield estimate. Also, if modules are fitted on a flat roof, the the angles can be changed. You get less module area ratio on flat roofs, do increasing yield is more important.

I have seen these, what happens when you manually slide the lever over?

I kind of get it, but this may help more. https://www.researchgate.net/post/What_is_the_difference_between_piled_raft_and_pile_group2

Though not clear, this is what PVGIS has to say , and show, about slope angle.

Also the modules may be getting the optimal amount of sunlight to reach peak efficiency. Too much light just turns into thermal energy, and you don't want that.

My neighbour, the slum landlord, was fitting some new windows the other day. Noticed there was no safety tag on the scaffolding, eventhough a proper company put it up. I think he found some windows as they don't match, and in one instance, don't even fit. Just wonder what it means when he comes to resell? I had to take out some indemnity insurance as the people selling could not find the FENSA certificate for the front door.