David001 Posted June 13 Share Posted June 13 (edited) Hello everyone. The roof of our outbuilding is of the metal industrial kind shown in the pic below. Last winter there were four wet spots on the ceiling below this roof showing that water had leaked in. So I can only imagine that the water got in through four of the fixings which hold the roof in place. The outbuilding was erected 12 years ago. Is it possible that some of the fixings have deteriorated, so as to let in rainwater? If so, I am thinking that perhaps I may be able to replace them myself, provided it's not difficult to do. Are there things I will need to be careful to do, and not do (beside falling off the roof!)? Or will I need to ask a roofer to do it? Thanks! David. Edited June 13 by David001 Better clarity. Link to comment Share on other sites More sharing options...
Tom Posted June 13 Share Posted June 13 (edited) If that's an actual picture of one of your fixings, and not just a picture from the net, then it doesn't look like it's tight enough against the panel. The EPDM washer needs to be snug but not crushed. Edited June 13 by Tom 1 Link to comment Share on other sites More sharing options...
ProDave Posted June 13 Share Posted June 13 2 comments, hope they are not harsh, but whoever put that roof on did a poor job imho. Firstly none of the fixings are in line, that shows a lack of care. Secondly, I always fix that sort of roof on the ridges. Little water flows down the ridges, it falls into the flat valleys and runs down there, so you don't really want fixings in the flat valleys where there is more water and more chance to leak. Agreed the one photographed close up does not look very tight. 1 Link to comment Share on other sites More sharing options...
Mr Punter Posted June 13 Share Posted June 13 I would keep the fixings you have and tighten them a little, so the washer is snug on the sheet. 1 Link to comment Share on other sites More sharing options...
David001 Posted June 13 Author Share Posted June 13 Thanks, everyone above, @Tom, @ProDave, and @Mr Punter, for your comments and advice. Yes, the man who put up that building, and who put its roof on, was a shoddy worker. It was a DIY job by a man who had spent his working life in an office, he then retired to the countryside, and was certainly confident that he could do all sorts of things. He had a lot of confidence, but in so many places around this property I've come across evidence of really shoddy decision-making and substandard workmanship. I zoomed in one of the fixings for the close-up without having decided which particular fixing to focus on. It seems from what you have said that I luckily focussed the camera on a fixing which shows the washer is not flush against the panel as it should be. So it seems that as soon as there's a warm dry day I ought to get up on the roof with a spanner and tighten each head so the washers are snug on the sheet, and then see whether there is any leaking after that. 1. Are the fixings above the EDPM washer made of plastic or metal? 2. If while I am checking them all and tightening them some of them break, are they standard? What would I look for online to order replacements, please? 3. Do I need to be careful where I put my weight? Where would be best to place my feet? Thanks. Link to comment Share on other sites More sharing options...
dpmiller Posted June 13 Share Posted June 13 probably a plastic cap pushed over a tek-screw 1 Link to comment Share on other sites More sharing options...
Tom Posted June 13 Share Posted June 13 1 hour ago, dpmiller said: probably a plastic cap pushed over a tek-screw Yep, I second that. Just flip the cap off with a screwdriver and then pinch the tek-screw up. Quicker and easier to use an impact driver than a spanner, but make sure you don't overtighten and crush the washer. 1 Link to comment Share on other sites More sharing options...
saveasteading Posted June 13 Share Posted June 13 Hooray something I know about. The screws are rather randomly fixed. Several areas seem to be missing fixings altogether, so the sheet is not properly fixed down and may disappear in a gale.. Crowns (the 'up' bits are screwed just a few times.) The close up of a crown is unlikely to be a culprit as not much water will reach it compared to the ones in pans. At least one of the plastic caps is not flush with the sheet. They are not seals, and only for show, but it suggests that the screws are not tight. Some of the screws may have missed the purlin, which is likely only 40mm wide.. They would have no purpose but have made a hole and will not have pulled tight. Mark the floor where the drips land as you will forget. You only need to tighten 4 screws at most. Drips can be direct from screws or they run either down the panel or along a rail to the lowest point. From this you can narrow the search area down to a few screws and fix the ones that need it. The tops of washers are usually aluminium. The rubbery bit will seal against the cladding in a primitive washer, or squeeze into the thread in a classy one. Apart from not being quite 'home' the other likely issue is when the screw has spun and the hole is too big, and the screw not gripping. For a bodge you take the screw out, squirt some mastic in and replace the screw, or use a new one. That lasts a few years and may be what is causing the problem. For a proper job, you need a screw with a wider diameter as it will cut a new thread and grip properly. We called them 'repair screws', but I don't think it is a common term. These don't need drilling heads as the hole is already there. The screws are turned using a Tek head. It is just a hex head but is the right size. Use a clutch drill to avoid over-tightening. It is worth getting these screws and heads from a specialist fixings supplier. Having written that I realise there are lots of possible problems, but just one proper solution. If a simple tightening doesn't work, then replace each (four?) with a slightly wider tek screw. Or just do that anyway. Be aware that more screws may also fail in time. There will be more errors than just the screws but if it is working I guess you live with it. You don't need new caps but it probabaly looks better with them. Plus. Don't fall off the roof, and don't lay your drill down or it will slide away. 1 Link to comment Share on other sites More sharing options...
David001 Posted June 14 Author Share Posted June 14 Thanks, everyone. @saveasteading, marking the floor where the drips land is good tip! (I took photos of the four wet spots on the very wide ceiling but your method will be much more helpful.) Is that black hexagonal top just "for show"? Is everything in pic 3, above, just a "slip-on" head with a washer beneath it protecting a screw? If so, should I prize off by inserting a screwdriver underneath the washer, or between the head and the washer? I'm just a 70-yr-old homeowner ho can attend to basic repairs. My tools are no more than a range of spanners, screwdrivers, hammers and other basic items. I don't know what a "clutch drill" is. 😁 Can I remedy the situation with the tools I have? THANK YOU. David. Link to comment Share on other sites More sharing options...
saveasteading Posted June 14 Share Posted June 14 marking the floor where the drips land is good tip! (I took photos of the four wet spots on the very wide ceiling but your method will be much more helpful.) Is that black hexagonal top just "for show"? The plastic caps are for show. Is everything in pic 3, above, just a "slip-on" head with a washer beneath it protecting a screw? No If so, should I prize off by inserting a screwdriver underneath the washer, or between the head and the washer? prise off the plastic cap and leave the washer alone until examined I'm just a 70-yr-old homeowner who can attend to basic repairs. My tools are no more than a range of spanners, screwdrivers, hammers and other basic items. I don't know what a "clutch drill" is. 😁 I should have said torque settings perhaps Can I remedy the situation with the tools I have? Yes. if the screws only need tightening then a socket spanner will do it. it will only need a half turn or so. To replace I'd suggest a battery drill is almost essential. most have torque settings. Borrow one? A socket spanner might do it? Im not recommending this but, in a push I have used a ladder , tied on to the gutter and 3 rungs past, in line with where I want to work. then if I was to slide, the ladder should provide restraint. Of course you really should have a scaffold to access and to catch you. the screw on the right has a plastic cap on it, as left. If you have a specialist fixings shop near then I'd recommend going there. Even for a tiny order they are likely to be very helpful, and they will have a variety of thread sizes. You will not need that self drill point. 1 Link to comment Share on other sites More sharing options...
Conor Posted June 14 Share Posted June 14 90% sure you'll just need an 8mm spanner for the screws. 1 Link to comment Share on other sites More sharing options...
George Posted June 14 Share Posted June 14 14 hours ago, saveasteading said: Hooray something I know about. The screws are rather randomly fixed. Several areas seem to be missing fixings altogether, so the sheet is not properly fixed down and may disappear in a gale.. Crowns (the 'up' bits are screwed just a few times.) The close up of a crown is unlikely to be a culprit as not much water will reach it compared to the ones in pans. At least one of the plastic caps is not flush with the sheet. They are not seals, and only for show, but it suggests that the screws are not tight. Some of the screws may have missed the purlin, which is likely only 40mm wide.. They would have no purpose but have made a hole and will not have pulled tight. Mark the floor where the drips land as you will forget. You only need to tighten 4 screws at most. Drips can be direct from screws or they run either down the panel or along a rail to the lowest point. From this you can narrow the search area down to a few screws and fix the ones that need it. The tops of washers are usually aluminium. The rubbery bit will seal against the cladding in a primitive washer, or squeeze into the thread in a classy one. Apart from not being quite 'home' the other likely issue is when the screw has spun and the hole is too big, and the screw not gripping. For a bodge you take the screw out, squirt some mastic in and replace the screw, or use a new one. That lasts a few years and may be what is causing the problem. For a proper job, you need a screw with a wider diameter as it will cut a new thread and grip properly. We called them 'repair screws', but I don't think it is a common term. These don't need drilling heads as the hole is already there. The screws are turned using a Tek head. It is just a hex head but is the right size. Use a clutch drill to avoid over-tightening. It is worth getting these screws and heads from a specialist fixings supplier. Having written that I realise there are lots of possible problems, but just one proper solution. If a simple tightening doesn't work, then replace each (four?) with a slightly wider tek screw. Or just do that anyway. Be aware that more screws may also fail in time. There will be more errors than just the screws but if it is working I guess you live with it. You don't need new caps but it probabaly looks better with them. Plus. Don't fall off the roof, and don't lay your drill down or it will slide away. Can I just check my understanding... for square sections you don't put fixings through the crown, only tight into the flat sections. For corrugated roofs it's the other way around and the fixings only go through the crowns. Link to comment Share on other sites More sharing options...
saveasteading Posted June 14 Share Posted June 14 52 minutes ago, George said: for square sections you don't put fixings through the crown, only tight into the flat sections. For corrugated roofs it's the other way around On old agricultural corrugated cladding, asbestos or galvanised, it was fixed by hook bolt from on top of the crown, to under the purlin. For modern cladding, which you are calling square, there are screws through the bottom/flat/ pan, directly into the purlin (or first through a skin of insulation) pulling it all tight. There are still some screws on the crowns to link the edges of adjoining sheets together. there should be mastic tape at these joints in most situations, to keep out water and draughts. If I wanted to fix corrugated cladding 1. I would question the choice. 2 it would be through the crowns but it would need special screws to resist the cladding ripping down over the thread. These have an additional coarse thread under the washer that should hold the sheet up if it gets stood upon. These are 'stand-off' screws but I wonder how commonly they are used. 1 Link to comment Share on other sites More sharing options...
George Posted June 14 Share Posted June 14 Thanks - didn't know about the lap screw. Corrugated fibre cement is still a popular choice for ag buildings. Link to comment Share on other sites More sharing options...
joe90 Posted June 14 Share Posted June 14 8 minutes ago, saveasteading said: These are 'stand-off' screws but I wonder how commonly they are used. I had not heard of those!!!! With my similar workshop roof I used tek screws on the flat sections and short ones on the crowns to hold the sheets together only (Cladco who supplied the sheets supplied info on how to fix). The only thing I did different was to use a membrane under the battens (like a tiled roof) to stop leaks or condensation in the building (worked very well). Link to comment Share on other sites More sharing options...
David001 Posted June 14 Author Share Posted June 14 @saveasteading, thanks for all your answers. Your 2 photos have made things clear. Thanks also for the tip re. using a ladder as a potentially helpful obstruction. I will tread carefully! David. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now