Skip to content
View in the app

A better way to browse. Learn more.

BuildHub.org.uk

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Toilet waste pipe placement

Featured Replies

So when running 40 or 50mm waste in concrete what should be the correct procedure? Push fit/compresion?

  • Replies 58
  • Views 29.7k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Nickfromwales
    Nickfromwales

    I think they should give us our own forum

  • Last Night an ex DJ Saved My Life   "There's not a problem that he can't fix 'Cause he knows all the tricksAnd if your pan gives you trouble…"   'Cause away goes trouble down the d

  • Think your going to have to get the kango bit sharpened up. Get 2 45 bends and put them together. You might need a small length of pipe in between the 2 bends maybe 5-7 inches long to get you in the c

Posted Images

Push fit....

 

Ideally you need to connect above slab if possible, or use 110mm below slab and use an entry fitting to do the transition. 

4 minutes ago, PeterW said:

Push fit....

 

Ideally you need to connect above slab if possible, or use 110mm below slab and use an entry fitting to do the transition. 

 

OK, thanks. Its going to be a BIG decision to dig the run from the 110mm to the sink up as its going to be close to UFH pipes.

Actually digging it up just isn't going to be a safe/easy option. Just managed to find this (zoomed) image of the offending pipework.

One corner of the sink waste goes across the UFH pipe. Its the pipe that was sat in the top of that grey boss that was un-bonded.

 

2018-02-21_10-03-37.jpg.f4afe65494624e7fcb9e4e777b9ae05f.jpg

I had this type of problem because a pipe moved after the slab was replaced. It was 110mm ducting for the water supply pipe and I used one of these to offset the entry a bit.

 

http://www.ebay.co.uk/itm/110mm-x-40mm-Waste-Pipe-Adaptor-/291514309082?item=291514309082&ViewItem=&nma=true&si=U4LuuKCsZavH%2BzIQ7TlciRWA2Z4%3D&orig_cvip=true&rt=nc&_trksid=p2047675.l2557

7 minutes ago, Barney12 said:

Actually digging it up just isn't going to be a safe/easy option. Just managed to find this (zoomed) image of the offending pipework.

One corner of the sink waste goes across the UFH pipe. Its the pipe that was sat in the top of that grey boss that was un-bonded.

 

2018-02-21_10-03-37.jpg.f4afe65494624e7fcb9e4e777b9ae05f.jpg

I'm no expert but that doesn't look right to me. I would have thought all that white pipe should be 110mm and under the slab not running through it.

8 minutes ago, Barney12 said:

Actually digging it up just isn't going to be a safe/easy option. Just managed to find this (zoomed) image of the offending pipework.

One corner of the sink waste goes across the UFH pipe. Its the pipe that was sat in the top of that grey boss that was un-bonded.

 

2018-02-21_10-03-37.jpg.f4afe65494624e7fcb9e4e777b9ae05f.jpg

 

Can't you just get your hand down there to clean the boss, brush on a good slug of solvent adhesive and push a bit of grey back down?

1 minute ago, PeterStarck said:

I'm no expert but that doesn't look right to me. I would have thought all that white pipe should be 110mm and under the slab not running through it.

 

Same here, not a good layout IMHO.

5 minutes ago, Onoff said:

 

Can't you just get your hand down there to clean the boss, brush on a good slug of solvent adhesive and push a bit of grey back down?

 

Yep, and I think that's what I'm going to have to do. The runs of 50mm are fairly short and there is only a couple of solvent bends.

Of course that does assume there is solvent on the other joints!!

I guess I can try and rig some sort of pressure test up?

Create an account or sign in to comment

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.