October 31, 20205 yr Author 1 minute ago, PeterW said: No... That screws onto the bottom of the tap, and will go all the way to the top tight under the tap itself leaving a piece of thread that the tap connector screws onto. Ok - got it ?
November 2, 20205 yr Author On 31/10/2020 at 12:29, PeterW said: Standard Hep2O 3/4 pipe connector is 29mm diameter across the points of the nut. https://www.wavin.com/en-ie/catalogue/Heating-Cooling/Plumbing-systems/Plumbing-Hep2O-Push-Fit/Hep2O-PB-Straight-Tap-Conn-WT-15x34 @pocster what is the internal diameter of those shrouds ..? Measure across the outer of the fixing the grub screw goes into. Didn’t have any on site . But based on the wavin measurements should fit ! So ordered . Shroud o/e is 35mm . ?
November 6, 20205 yr Author AH! Bum !! So near ! The problem is the bsp fitting on the Hep2o won’t fit in the shroud . The shroud this end has an internal lip probably only 1mm but enough to stop it going in ?
November 6, 20205 yr Author Shows the issue better . I suppose in theory I could angle grind the bsp nut - but what a pita !
November 6, 20205 yr 3 minutes ago, pocster said: Shows the issue better . I suppose in theory I could angle grind the bsp nut - but what a pita ! Do you know anyone with a lathe who could take the corners off your nuts neatly?
November 6, 20205 yr 1 minute ago, joe90 said: Nah, tighten it up then file/grind the corners off, it’s not that much too big. Philistine
November 6, 20205 yr I would spin the corners off on my lathe. But a file will do, it's not as though you will see the finished thing. Of course if you had the proper supplied tap connector it would fit.
November 6, 20205 yr Author 13 minutes ago, Onoff said: Do you know anyone with a lathe who could take the corners off your nuts neatly? That would hurt too much
November 6, 20205 yr Author 1 minute ago, ProDave said: I would spin the corners off on my lathe. But a file will do, it's not as though you will see the finished thing. Of course if you had the proper supplied tap connector it would fit. There never was a supplied connector - you simply got f all with it ?
November 6, 20205 yr 22 minutes ago, pocster said: AH! Bum !! So near ! The problem is the bsp fitting on the Hep2o won’t fit in the shroud . The shroud this end has an internal lip probably only 1mm but enough to stop it going in ? Hold on, you have the nut on the tap there. you don't need that. Take the nut off and the washer and screw the adaptor bit straight onto the tap then it will go all the way on.
November 6, 20205 yr Author 5 minutes ago, joe90 said: Nah, tighten it up then file/grind the corners off, it’s not that much too big. That’s what I reckon . Everyone else has a mate with a lathe . I have no friends ? and therefore no access to a lathe ?
November 6, 20205 yr Author Just now, ProDave said: Hold on, you have the nut on the tap there. you don't need that. Take the nut off and the washer and screw the adaptor bit straight onto the tap then it will go all the way on. Yeah I know the nut needs to come off . It just stays there for now so it doesn’t get lost - even though I shouldn’t need it
November 6, 20205 yr 1 minute ago, pocster said: Yeah I know the nut needs to come off . It just stays there for now so it doesn’t get lost - even though I shouldn’t need it So take the nut and washer off, screw the adaptor on, screw the tap connector on and try and assemble it. I am sure you said the nut on the tap connector goes down the main tube?
November 6, 20205 yr Author 28 minutes ago, ProDave said: So take the nut and washer off, screw the adaptor on, screw the tap connector on and try and assemble it. I am sure you said the nut on the tap connector goes down the main tube? Yes - the problem is the nut on the Hep2o fitting - that’s needs filing
November 6, 20205 yr Well file it then, just enough to go down the tube, still leaving enough flat to get a spanner on.
November 6, 20205 yr Author 1 hour ago, ProDave said: Well file it then, just enough to go down the tube, still leaving enough flat to get a spanner on. ?
November 6, 20205 yr 4 minutes ago, pocster said: ? If...you could get a bit of 15mm pipe into that fitting you could hold in the 16mm chuck of a pillar drill like a poor man's vertical lathe and file it like that. A bit hairy but done that more than once. Wash your hands well btw, brass splinters are horrible.
November 6, 20205 yr Author 19 minutes ago, Onoff said: If...you could get a bit of 15mm pipe into that fitting you could hold in the 16mm chuck of a pillar drill like a poor man's vertical lathe and file it like that. A bit hairy but done that more than once. Wash your hands well btw, brass splinters are horrible. That sounds like an imminent accident- I’ll try and file it with dremel ...
Create an account or sign in to comment