Kilt Posted January 18, 2022 Share Posted January 18, 2022 Looking for recommendations for insulation around window reveals. Just had new upvc sash windows put in our barn conversion, replacing rotten old ones, however the new frames are far thinner than old, (window company cockup) so im struggling with some of the reveals and getting some insulation in there. The tightest clearance is 20mm. Looking for advice. I had thought about using super quilt, but without the recommended battons, or using some insulated board of some form. I even tried Wedi board, but it’s too brittle to support a plaster finish and kids. attached photo is of one of the better reveals, I’ve been able to get battons and 20mm PIR in here. Link to comment Share on other sites More sharing options...
Radian Posted January 18, 2022 Share Posted January 18, 2022 What's to stop you cutting some of the rubble back to square it up and create enough space for a decent thickness insulation backed plasterboard circa 40mm? 1 Link to comment Share on other sites More sharing options...
pudding Posted January 18, 2022 Share Posted January 18, 2022 Aerogel if its gotta be thin and is a small area like just reveals? 1 Link to comment Share on other sites More sharing options...
DragsterDriver Posted January 18, 2022 Share Posted January 18, 2022 I’d ask the window company who didn’t allow ‘add ins’ to the frames what they suggest. Link to comment Share on other sites More sharing options...
Kilt Posted January 18, 2022 Author Share Posted January 18, 2022 1 hour ago, Radian said: What's to stop you cutting some of the rubble back to square it up and create enough space for a decent thickness insulation backed plasterboard circa 40mm? A lot of the stone work is lime mortar, or soil based, so any disturbances, create massive movements. It’s all rubble/field stone, some are massive stones, so I could end up with some pretty big holes! ? Link to comment Share on other sites More sharing options...
Kilt Posted January 18, 2022 Author Share Posted January 18, 2022 2 minutes ago, DragsterDriver said: I’d ask the window company who didn’t allow ‘add ins’ to the frames what they suggest. Dot and dab foil backed 9mm PB was their answer. the worst offending area, I kicked off, as there isn’t sufficient margin for any build up. they’re coming back in spring to take window out and alter stone work for that one. . 1 Link to comment Share on other sites More sharing options...
DragsterDriver Posted January 18, 2022 Share Posted January 18, 2022 9 minutes ago, Kilt said: Dot and dab foil backed 9mm PB was their answer. the worst offending area, I kicked off, as there isn’t sufficient margin for any build up. they’re coming back in spring to take window out and alter stone work for that one. . what? That’s no good. ask for a structural engineers report from them stating how much bearing they can remove from the lintel above. Without being a complete ‘meldrew’ they’d be changing all my windows. Link to comment Share on other sites More sharing options...
Radian Posted January 18, 2022 Share Posted January 18, 2022 16 minutes ago, Kilt said: A lot of the stone work is lime mortar, or soil based, so any disturbances, create massive movements. It’s all rubble/field stone, some are massive stones, so I could end up with some pretty big holes! ? Was actually thinking more of diamond disc cutter than bashing with chisel but I understand if you feel that might be too disruptive. Link to comment Share on other sites More sharing options...
JohnMo Posted January 18, 2022 Share Posted January 18, 2022 You can use Aerogel, which give bout 20% improved performance over PIR for the same thickness, for 3x the cost. Or get some thin PIR and foam into place Link to comment Share on other sites More sharing options...
Cpd Posted January 18, 2022 Share Posted January 18, 2022 7 hours ago, Radian said: Was actually thinking more of diamond disc cutter than bashing with chisel This is what I would do, you could easily take 50mm back without a drama and then go 50mm PIR and plasterboard stuck to that. Link to comment Share on other sites More sharing options...
Kilt Posted January 22, 2022 Author Share Posted January 22, 2022 cheers for replies. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now