SBMS

Thanks @Iceverge - I'm trying to minimise installation effort so was trying to get a rafter depth that meant I could just use blown in cellulose. Whilst I could extend the depth of the rafters internally, with the additional labour and timber, I wonder if I'd be better off just going for deeper rafters or I-Joists like @joe90 mentioned - even if there's additional cost?

Did you full fill or manage to create a cavity somehow? What’s the performance like?

Thanks @ETC will do once I’ve got the section drawings back. Only got elevations and planning drawings at the moment, unless you can work it out from these and floor plan.

@joe90what did you insulate with?

The only option for a shallower rafter is PIR. We did that on our previous build which also had attic trusses/ rooms in roof. Whilst the h value is okay the top floor gets very warm in warm weather due to the lower thermal mass (or whatever you call it) of the rigid insulation. I also don’t like the fact that timber shrinks, PIR then isnt tight and thermal bridging increases and performance is affected. if there’s another solution that gives high mass and low thermal decay in a smaller rafter am all ears?

Has anyone any experience of a loose cut roof with 300mm deep rafters? We were looking to use posi rafters at 304mm to get the depth for blown cellulose but it doesn’t appear to be a good fit as we’ve got two roofs running into each other with rooms in the roof. It’s looking like attic trusses are out for the same reason. I believe we can get 300mm rafters which might work, or could potentially look for an engineered I-beams. Any gotchas with this approach?

I'd advise against judicial review and instead re-apply with a full matters application with a planning consultant assistance. Judicial review won't look at the merits of your application, but whether there was a legal mistake made by the inspector - facts in law. So you'd have to identify specifically what legal mistake was made, and even if you were successful at judicial review (£££), all that happens is that the inspector re-assesses taking that legal point from the high court. So you'd have to specifically point to a specific error in law made by the inspector. Even then they might make the same decision.

Good Luck, your plot looks fantastic 👍

I feel for you. I think that where a planning consultant would have assisted is in providing objective similar schemes that had been approved and drawing comparisons to your site and those. Where travel was an issue they would have looked for similar schemes that had been passed, on evidence, that were objectively ‘worse’ than yours. They reference planning policy, high court cases that challenge and reinforce your position and your site. Fundamentally, at an appeal stage, you’re into the intricacies and minutia of planning law, planning policy and case law. At this stage it’s very hard as a lay person to produce a compelling and reasoned argument. It’d be a bit like representing yourself in court. I also think that an appeals officer or planning officer treats an application differently when you have an advocate that understands planning and case law in detail. You sound a bit like me, trying to understand the NPFF, applying reasoned logic, ‘tilted balance’ and so on. But here’s the reality - actually what you need is not to understand and interpret the NPFF and planning policy, but to understand how your planning department and an inspector understands and interprets planning policy. This is totally different to you understanding policy, because the missing piece you won’t have is experience. Experience of national prior cases, of supporting high court rulings, of the local interpretations and sites that were passed and so on. Unfortunately, it’s not an intellectual argument, and it’s not a case of you presenting your argument to a panel of other lay people or a jury - it’s their decision to make - entirely on their interpretation and their application of policy to your application. I don’t know how It works with going back in for planning after a dismissed appeal but I would 100% recommend appointing an experienced consultant and speaking to them about your chances going for a full application (not outline). A good one will 100% be able to tell you if you have a case. Waiting for your planning officer or head of planning to come back on your points is a waste of time, I think. Get back on the saddle, get a professional in your corner, and see if the game’s over or time for round 2. 👊

Around here, the term ‘sustainability’ in terms of the paragraph being quoted from the NPFF seems to have been interpreted as the sustainability of transportation - ie the sustainability of accessing the site. So in our council district, zero weight is given to the eco or carbon ‘sustainability’ of the build. I don’t know what the intended definition is but thought I would mention it because of the references to Passivhaus re ‘sustainability’ which isn’t the interpretation here. The weight is given to how easy it is for non car based transportation links - ie proximity to bus routes, distance from a village centre etc. I absolutely think that engaging a planning consultant is the way to go, by the way.

Interesting. Any others out there putting a VCL on inside leaf of masonry? Will chat through this with architect, see what they think.

@SteamyTea is this correct - that a cavity masonry should have a VCL then?

That makes sense - so does the dew point move further toward the outer leaf based on the size of the cavity? Does this make denser full fill (like cavity batts) higher risk (I understand there's a problem of wicking across the cavity, but am I right in thinking interstitial condensation is moisture travelling from the inside out?

Thanks nod - but we're using blown in beads, not cavity board. Anybody had to look at VCL with a cavity and blown beads - or a cavity with a full fill rockwool for example?

So not required?

Possibly a stupid question that demonstrates my lack of understanding but… is a VCL required or recommended on a masonry cavity wall, and if not why not? Speaking mainly about an EPS bead full fill cavity. I sense not, and my guess is down to the wall makeup versus timber frame where the vapour permeability goes from low to high to encourage ‘drying out’.. does this principle not apply to masonry? Or just not to the same amount?

Interesting... guy from warmcel told me we needed a very vapour impermeable layer for the inner roof makeup (Propassiv best - OSB cheapest) but said we couldn't use Plaster board (and that the pressure from the Cellulose blower could blow it off). Is that rubbish?

If you did it again would you try and get them to fill before plasterboard has been fitted?

Would you recommend cellulose again? How deep did you go?

Thanks @Duncan62. Any reason you went wood fibre over cellulose?

Was that a full fill? What U Value did you achieve with that?

Thanks Liam. When was that? Did they give any additional costs for 300mm or higher?

@Kelvin Did you ditch the idea of cellulose? What did you go for?

Currently assessing a blown cellulose product for our attic rooms and roof.. Anybody got any recommendation on suppliers/installers? So far have found Warmcel (awaiting call back) and Thermofloc (made by Thermafleece). Thermofloc tell me they're no longer doing blown cellulose installation. At the moment am considering switching to another blown product for the roof (such as blown mineral wool) purely because of the lack of installers (we're not DIYing it). It does make me wonder how common a product it is, outside of this forum (and the use of MBC, which is across this forum and where they use cellulose extensively, but presumably install it using their own teams?) Anybody got any recommended installers? UK, north west.

Got you. Useful to know whilst we are pre drawings stage. Does anyone else know if this is a common ask with cellulose blown roofs?MBC profile doesn’t seem to have a 50mm ventilation gap.