Skip to content
View in the app

A better way to browse. Learn more.

BuildHub.org.uk

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Problems with the Disinfection Cycle

Featured Replies

Hi, got a major problem with my disinfection cycle which makes no sense to me, On my LG 9Kw heat pump controls I set the disinfection control to come on at required time and for 1 hour to get water temp up to 60°C When the required time is reached I hear the solenoid click in for the immrsion heater, after 1 hr the temprature has risen about 2° C. the water temp was 50°C to start with.

I have checked the flow of current to the immerson heater with a clamp meter which is a healthy 13.5 amps, I have checked the resistance of the immersion heater element which was 19 ohms, I have two more thermometers in the pocket of the water tank which also only rise 2° in 1 hr. I have also tried to check the thermostat on the immersion heater , which does switch on and off and is turned up to the top.

Anybody got any Ideas what to check next. Thanks

Are you sure the bottom of the immersion reaches down to the level of the temperature sensors?? The immersion will only heat as far as it reaches down.

If youve seen it drawing 13amps then that energy has to be going somewhere either heating the water in the cylinder or heating water that is being constantly drawn off.

Have you monitored the current over time? Is the immersion switching on and off (thermally limited by it's internal thermostat)?

How old is this install? Live in a hard water area?

Scale build up around heating elements can reduce heat output. Though it only slows it down doesn't make the heat disappear.

  • Author
5 hours ago, -rick- said:

Have you monitored the current over time? Is the immersion switching on and off (thermally limited by it's internal thermostat)?

How old is this install? Live in a hard water area?

Scale build up around heating elements can reduce heat output. Though it only slows it down doesn't make the heat disappear.

Hi, I am going to change the immesion thermostat to see if that helps, the instal is only 2.5 years old,but to be honest I dont think it worked from new, we dont live in a hard water area

Just now, Potatoman said:

Hi, I am going to change the immesion thermostat to see if that helps, the instal is only 2.5 years old,but to be honest I dont think it worked from new, we dont live in a hard water area

That sounds a bit like jumping the gun. If you've measured the full 13A current draw then the thermostat was working when you measured.

My question was more around whether the thermostat is turning the immersion on and off (ie, it thinks the tank is to temp) when the tank is not to temp. If that is happening then it might be that the immersion has thorough scaled up and can't shed the heat fast enough.

  • Author
9 hours ago, Dillsue said:

Are you sure the bottom of the immersion reaches down to the level of the temperature sensors?? The immersion will only heat as far as it reaches down.

If youve seen it drawing 13amps then that energy has to be going somewhere either heating the water in the cylinder or heating water that is being constantly drawn off.

Good point about the energy going somewhere, not sure where though,. The immersion heater is fitted at the side 4/5 the way down and the pocket for the temperature sensors is about 3/4 the way down directly above the Immersion heater .

How big is your tank?

Do you have a pumped loop hot water system that is active or even an accidental thermosypon that is dissapating the heat?

  • Author
1 hour ago, -rick- said:

That sounds a bit like jumping the gun. If you've measured the full 13A current draw then the thermostat was working when you measured.

My question was more around whether the thermostat is turning the immersion on and off (ie, it thinks the tank is to temp) when the tank is not to temp. If that is happening then it might be that the immersion has thorough scaled up and can't shed the heat fast enough.

I supose it could be, but we dont live in a hard water area, its only 2.5 years old and I am not sure but I dont think it has been working since new. As for changing the thermostat,I am just running out of ideas,going to change the immesion heater next, if that doesn't work.

Create an account or sign in to comment

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.